Gauge For Lampholders E40 E14 High Pressure Gauge For Lampholders
List:
| 7006-25-7 | “GO” GAUGE FOR SCREW THREADS OF LAMPHOLDERS E10, E14 AND E40 |
| 7006-26-4 | “NOT GO” GAUGES FOR SCREW THREADS OF LAMPHOLDERS
E10,EP10,EY10,E14,E27,E39 AND E40 |
| 7006-30-2 | PLUG GAUGE FOR E14 LAMPHOLDER FOR TESTING CONTACT-MARKING |
| 7006-30A-1 | E14 PLUG GAUGE FOR LAMPHOLDERS E14 WITH CANDLE SHAPED SHAFT FOR
CANDLE LAMPS FOR TESTING CONACT-MARKING |
| 7006-31-5 | E14 GAUGE FOR TESTING CONTACT-MARKING AND PROTECTION AGAINST
ACCIDENTAL CONTACT DURING INSERTION OF LAMPS IN LAMPHOLDERS |
| IEC60238 Figure5 | E14 Test Cap for torque test clause 18 of IEC60238 |
| IEC60238 Figure11 | E14 Test Cap for temperature test 14.4 and 19.3 of IEC60238 |
| IEC60238 Figure 13 | E14 Test cap A for lampholders E14 of IEC60238 |
| IEC60238 Figure 13 | E14 Test cap B for lampholders E14 of IEC60238 |
GO GAUGE FOR SCREW THREADS OF LAMPHOLDERS E10, E14 AND E407006-25-7
PURPOSE:
To check the minimum dimensions of the lampholder screw thread and
dimension X show on sheet 7005-20
TESTING :
It shall be possible to screw the gauge into the lampholder without
using undue force.
(For the torque to be applied in case of doubt, see IEC 60238 ,
subclause 4,4).
When the gauge has been screwed in as far as it will go, the rim of
the screw shell of the lampholder shall be co-planar with, or
project beyond Y1, but it shall be not project beyond surface Y2.
7006-26-4
“NOT GO” GAUGES FOR SCREW THREADS OF LAMPHOLDERS
E10,EP10,EY10,E14,E27,E39 AND E40
PURPOSE:
To check the minimum dimensions of the screw thread, dimension D1,
of lampholders E10, EP10, EY10, E14, E27, E39 AND E40.
TESTING:
The screw thread of the lampholder shall be assumed to be correct
if the gauge does not enter by its own weight so far that the
thread protrudes beyond surface T.
PLUG GAUGE FOR E14 LAMPHOLDER FOR TESTING CONTACT MAKING
PLUG GAGUE FOR LAMPHOLDER E14 WITH CANDLE SHAPED SHAFT FOR CANDLE
LMPS FOR TESTING CONTACT MAKING
GAUGE FOR TESTING CONTACT-MAKING AND PROTECTION AGAINST ACCIDENTAL
CONTACT DURING INSERTION OF LAMPS IN LAMPHOLDERS E14
PURPOSE: To check E14 lampholders in respect of:
a) Contact-making with lamps having adverse dimensions.
b) Protection against accidental contact with live parts, viz. the
cap shell, during insertion of a lamp.
TESTING: The holder is connected in the test circuit as shown.
a) With switch A in position 2 and switch B open, the gauge is
screwed fully home.
In this position, both lamps shall light.
b) With switch A in position 1 and switch B closed, the gauge is
screwed in slowly until either of the lamps lights.
With the gauge held in this position, switch B is opened and the
test probe at the side of the gauge is slid downwards as far as
it will go into the space between the gauge and the holder.
In this position the lamps shall not light.
7006-25-7
“GO” GAUGE FOR SCREW THREADS OF LAMPHOLDERS E10, E14 AND E40
7006-26-4
“NOT GO” GAUGES FOR SCREW THREADS OF LAMPHOLDERS
E10,EP10,EY10,E14,E27,E39 AND E40
7006-30-2 .
PLUG GAUGE FOR E14 LAMPHOLDER FOR TESTING CONTACT-MARKING
7006-30A-1
E14 PLUG GAUGE FOR LAMPHOLDERS E14 WITH CANDLE SHAPED SHAFT FOR
CANDLE LAMPS FOR TESTING CONACT-MARKING
7006-31-5
E14 GAUGE FOR TESTING CONTACT-MARKING AND PROTECTION AGAINST
ACCIDENTAL CONTACT DURING INSERTION OF LAMPS IN LAMPHOLDERS
IEC60238 Figure5 E14 Test Cap for torque test clause 18 of IEC60238
IEC60238 Figure11 E14 Test Cap for temperature test 14.4 and 19.3
of IEC60238
IEC60238 Figure 13 E14 Test cap A for lampholders E14 of IEC60238
IEC60238 Figure 13 E14 Test cap B for lampholders E14 of IEC60238
60399-IEC-04-1
“GO” Gauge for barrel thread of lampholders with shade holder ring
E14
“Not GO” Gauge for barrel thread of lampholders with shade holder
ring E14
