IEC62368 Figure V.1 V.2 V.3 V.4 V.5 Telecom Terminal Test Probes
| IEC62368 probe no. | Probe Name |
| IEC 62368 Figure V.1 | Jointed test probe for equipment likely to be accessible to
children |
| IEC62368 Figure V.2 | Jointed test probe for equipment like to be accessible to children |
| IEC62368 Figure V.3 | Blunt probe, Telecom Test Probe |
| IEC62368 Figure V.4 | Wedge probe |
| IEC62368 Figure V.5 | Terminal probe |
I) IEC 62368 Figure V.1 Jointed test probe for equipment likely to
be accessible to children
conforms to many standard requirement of
IEC 62368 Figure V.1
UL474 Fig 5.1
UL507 Fig 9.2(PA100A)
UL982 Fig 7.1
UL1017 Fig 2
UL1062 Fig1.2
UL1278Fig 8.3
UL1310 Fig 16.2
UL60065 Fig14
and UL60950 Fig NAF.1.
Palm simulator and restricted joint movement simulates human finger
movement.
The UL accessibility probe is also called UL articulated probe or
jointed test finger probe.
It is widely used in the enclosure protection test of the
electrical equipment.
II)IEC 62368 Figure V.2 Jointed test probe for equipment like to be
accessible to children
This is a precision test finger made in accordance with many
standards like
IEC 62368 Figure V.2
IEC 61032 figure 2,
IEC60950 figure 2A,
IEC60884,
IEC60335,
UL507,
and UL1278 figure 8.4.
This probe is intended to verify the basic protection against
access to hazardous parts. It is also used to verify the protection
against access with a finger. This test finger probe consists of
dito, finger, base and insulated handle which simulates the
characteristics of the human hand. It has two movable joints, which
can be curved at 90°.
Customizable: it can be used for anti-electric shock test when
equipped with pluggable banana plugs and amphenol connector at the
end of the handle , or used for enclosure protection test when open
threaded hole of M6 at the end of the handle (connected with pull
and push dynamometer).
III)IEC62368-1 Figure V.3-Blunt probe, Telecom Test Probe
Required by IEC60950 fig 2C, IEC 62368 figure V. 3, EN, and some UL
and CSA standards to test accessibility to TNV circuits (telecom).
The handle and stop face are nylon, the tip is stainless steel.
For a plug, jack, or connector, the blunt probe of IEC62368-1
Figure V.3 is applied without appreciable force and in any possible
position to the
plug, jack, or connector.
IV)IEC62368-1 Figure V.4 Wedge probe
IEC62368-1 Figure V.4 UL Test Bent Finger Probe PA100A Test Bent
Finger Probe
1, According to : IEC62368-1 Figure V.4 UL507 (PA100A), UL1017
figure 2, figure 6.5 UL1062, UL982 figure 7.1 and figure 1.2 UL474
figure 5.1 and figure 14, UL60065 UL6500 figure 14, Figure 7.2 and
figure 8.3 UL1278 UL1082
2, Mainly used for the inspection to prevent the body touch
dangerous live parts,heating or hot parts, mechanical components,
as well as inspection of solid foreign bodies into the equipment.
It is necessary for protection against electric shock test of
household and similar electrical appliances
3,This is the "UL" test finger, researched and designed by UL and
required by most UL Standards. Palm simulator and restricted joint
movement simulates human finger movement. Made of all nylon.
Bell-Core accessory available.The handle is made of nylon. The
finger is made of stainless steel.
| Test finger length | 234mm |
| Knurled length | 30/30/40mm |
| Material | stainless steel and nylon |
| Reference | IEC62368-1 Figure V.4
UL507,UL982,UL1278,UL1062,UL1310,UL474,UL60065 |
V)IEC62368-1 Figure V.5 Terminal probe
This probe conforms to the standard requirement of IEC62368-1
Figure V.5 IEC61032 figure 4 test probe D and IEC60529 for IP4 and
IEC60065.
This rod probe is intended to verify the protection of persons
against access to hazardous parts.
It is also used to verify the protection against access with a
wire.
Customizable: It can be used for anti-electric shock test when
equipped with amphenol connector.
Or used for enclosure protection test when open threaded hole of M6
at the end of the handle (connected with pull and push dynamometer)
.
The probe whose model number is with "T" is with force.
